ASTM A682 PDF

ASTM A Standard Specification for Steel Strip, High Carbon, Cold Rolled, General Requirements. Find the most up-to-date version of ASTM A at Engineering ASTM A, AM – Designation: A /A M – 02 An American National Standard Standard Spe.

Author: Akizshura Tojanris
Country: Morocco
Language: English (Spanish)
Genre: Art
Published (Last): 13 October 2007
Pages: 353
PDF File Size: 13.27 Mb
ePub File Size: 14.72 Mb
ISBN: 165-9-24626-175-3
Downloads: 59709
Price: Free* [*Free Regsitration Required]
Uploader: Zura

A portion of the coil may be discarded prior to cutting the samples for retest. Notwithstanding the absence of a signature, the organization submitting the EDI transmission is responsible for the context of the report.

The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Unless otherwise agreed to, all tests and inspections, except product analysis, shall be made at the place of production.

ASTM A Steel, Strip, High Carbon, Cold Rolled, General Requirements

qstm However, under SI the preferred term in mass. Two additional samples are secured from each end of the coil from which the original sample was taken. However, the document shall clearly identify the organization submitting the document. Rework and Retreatment NOTE 2—Camber tolerances as shown in the table are for any 8 ft.

This is produced when the edge condition is not a critical requirement for the?

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such asm, are entirely their own responsibility. Table 3 shows requirements for additional elements. This standard has been a6822 for use by agencies of the Department of Defense.

  LYGODIUM FLEXUOSUM PDF

The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. NOTE 2—Camber tolerances as shown in the table are for any mm length. The values listed are not exact conversions of the values listed in the inch-pound tables but instead are rounded or rationalized values.

ASTM A682 Grade 1074

However, unless the order speci? If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. When required, minimum coil weights are subject to negotiation. B Measured 10 mm or more in from edge; and on narrower than 25 mm, at any place between edges.

However, under SI the preferred term in mass. When agreed by purchaser and supplier, other silicon ranges are permissible. When the amount of vanadium, columbium, astj titanium is less than 0. NOTE 1—Camber is the greatest deviation of a side edge from a straight line, the measurement being taken on the concave side with a straight edge.

This specification covers the general requirements for cold-rolled carbon spring steel strip in coils or cut lengths. Over 12 Through 11? Combining values from the two systems will result in nonconformance with the specification. For strip length under 8 ft.

  DS14C232CN DATASHEET PDF

Awtm values from the two systems will result in nonconformance with the speci? Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Combining values from the two systems will result in nonconformance with the specification. Each of the elements listed in Tables 2 and 3 and additional elements agreed upon by the purchaser and the supplier shall be included in the report of heat analysis. Note 1—The term weight is used when inch-pound units are the standard. General Requirements for Delivery 4. NOTE 2—The industry de? Last previous edition A — Conformance to SI tolerances is mandatory when the “M” specification is used. Your comments are invited either for revision of this standard zstm for additional standards aatm should be addressed to ASTM International Headquarters.

C Number 3 edge strip with thickness tolerance guaranteed at less than 3? Conformance to SI tolerances is mandatory when the s682 specification is used. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

Thickness Tolerances Plus or Minus, in. When one or more of these elements is speci? Over 12 Width Tolerance, Plus and Minus, in. Originally published as A —